説明
Description: This tool is a photoresist or polyimide coater that uses an extrusion or slot die head to scan across the substrate. Two different slot die heads are used, one for positive photoresist and another slot die head for polyimide coating. The chemical is extruded through the slot die head by using an extremely accurate pump and out through a fine gap lip that then scans across the substrate (glass panel). The height above the substrate is repeatability-determined by Keyence lasers that constantly measure the height above the substrate while scanning. Once the lasers are calibrated to the surface of the substrate, the slot die head will maintain a specified gap while scanning to ensure a uniform and repeatable thickness coated film. **No bake ovens are supplied with this tool, softbake oven bakes were done using a separate standalone hot plate oven or EVG Softbake ovens.構成
Name: Extrusion Deposition System Model: Advantage II Power Requirements: 240 VAC, 3-Phase (4-Wire), 30 A, 50/60 Hz Air Requirements: CDA - 100 psi @ 4-6 SCFM Water Requirements: DI Water - 10 L/min Weight: 4600 lbs. Specifications: Positive Resist: .5 µm to < 10 µm (Low Viscosity Die) Polyimide coating thickness: 5 um to < 20 µm (High Viscosity Die) Coating Uniformity within each panel: ±5% factory spec, typically ±3% Substrates: Gen II glass .7 mill thickness, 370 mm by 470 mm Chemicals used: AZ1505 positive photoresist, U-Varnish 2000 polyimide, Propylene Glycol Methyl Ether Acetate (PGMEA) Techniques: Photoresist coating, polyimide coatingOEMモデルの説明
提供なしドキュメント
ドキュメントなし
カテゴリ
Coaters & Developers
最終検証： 60日以上前
主なアイテムの詳細
状態：
Used
稼働ステータス:
Deinstalled / Uncrated
製品ID：
128810
ウェーハサイズ：
不明
ヴィンテージ：
2010
Logistics Support
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
nTACT
ADVANTAGE II
カテゴリ
Coaters & Developers
最終検証： 60日以上前
主なアイテムの詳細
状態：
Used
稼働ステータス:
Deinstalled / Uncrated
製品ID：
128810
ウェーハサイズ：
不明
ヴィンテージ：
2010
Logistics Support
Available
Transaction Insured by Moov
Available
Refurbishment Services
Available
説明
Description: This tool is a photoresist or polyimide coater that uses an extrusion or slot die head to scan across the substrate. Two different slot die heads are used, one for positive photoresist and another slot die head for polyimide coating. The chemical is extruded through the slot die head by using an extremely accurate pump and out through a fine gap lip that then scans across the substrate (glass panel). The height above the substrate is repeatability-determined by Keyence lasers that constantly measure the height above the substrate while scanning. Once the lasers are calibrated to the surface of the substrate, the slot die head will maintain a specified gap while scanning to ensure a uniform and repeatable thickness coated film. **No bake ovens are supplied with this tool, softbake oven bakes were done using a separate standalone hot plate oven or EVG Softbake ovens.構成
Name: Extrusion Deposition System Model: Advantage II Power Requirements: 240 VAC, 3-Phase (4-Wire), 30 A, 50/60 Hz Air Requirements: CDA - 100 psi @ 4-6 SCFM Water Requirements: DI Water - 10 L/min Weight: 4600 lbs. Specifications: Positive Resist: .5 µm to < 10 µm (Low Viscosity Die) Polyimide coating thickness: 5 um to < 20 µm (High Viscosity Die) Coating Uniformity within each panel: ±5% factory spec, typically ±3% Substrates: Gen II glass .7 mill thickness, 370 mm by 470 mm Chemicals used: AZ1505 positive photoresist, U-Varnish 2000 polyimide, Propylene Glycol Methyl Ether Acetate (PGMEA) Techniques: Photoresist coating, polyimide coatingOEMモデルの説明
提供なしドキュメント
ドキュメントなし